HFR2-SU3S2

AvailabilityOut of stock
SKU
PB-HFR2-SU3S2
  • Support 3.5" HDD SATA I/II/III 4 Bays Maximun 8 TB per drive (8x4=32)
  • SATA III Transfer rate up to 6Gbps
  • Hot-Swap
  • Raid mode JBOD / RAID 0, 5, 10, 50
  • USB 3.0Transfer rate up to 5.0 Gbps
  • eSATATransfer rate up to 6.0 Gbps
  • LED monitor
  • Function Gbps Smart Fan
  • 1 Year waranty by back-n.co.ltd.,
  • ฿6,950.00

    10 Times Faster

    The full-duplex data transfers capability allows the sending and receiving of data (at the same time) at 10 times faster than an equivalent card of USB 2.0 Standard. The maximum speed of USB 3.0 is 5Gbps, which enables the data transfer up to 25GB within a minute.

    Supports 32 TB

    Maximum addressable capacity 32TB via the USB 2.0 / USB 3.0 interfaces. Native 4KN Hard Drive Not Supported.

    POWER SYNC

    Powers off in synchronizatin with PC.

    HDD X 8 (Supported)

    All 8 HDDs are recognized when they are installed.

    SMART FAN

    Comes with auto / manual modes & 3 levels of speed for best convention. Smart Fan functions:


  • Thermal-sensor built-in
  • Auto & manual modes
  • 3 levels of speed

  • Single Mode

    Non-RAID: (Single Mode) Computer will show up as two independent drives. This function can be used if RAID is not required, if one HDD is installed or two different brands or capacities of HDD are installed.

    Spanning Mode

    Spanning concatenates multiple hard drives as a single large volume; resulting in a seamless expansion of virtual volumes beyond the physical limitations of separately connected hard drives. The data are written frim HDD1 to HDD8. RAID 0, JBOD Spanning Only, Non-Single JBOD

    Striping Mode

    Striping is a method of concatenating multiple hard drives into one logical storage unit. It is the automated process of writing data across multiple drives simultaneously. Striping is used to increase the performance of disk reads. The multiple hard drives will write data in “column” effect. If one drive in a striped set fails, all of the data in the stripe set is lost.

    RAID 50

    RAID 50 combines multiple RAID 5 arrays with RAID 0 Striping. RAID 50 offers highest level of redundancy and performance. RAID 50 can sustain one to four drive failures while maintaining data integrity if each failed disk is in a different RAID 5 array. In RAID 50 the total addressable volume is 2 times the smallest layer of RAID 5 array. RAID 50 requires at least 6 Hard drives.

    RAID 1 + 0

    RAID 1+0 is mirrored(Raid 1) sets in a striped(Raid 0) set .

    Interface
  • USB 3 .0 Super speed
  • Data Transfer Rate
  • USB 3.0 : up to 5.0Gbps
  • Maximum HDD size
  • 6 TB (Native 4KN Hard Drive Not Supported.)
  • HDD
  • 3.5″ SATA I / II / III HDD
  • Supports 4 HDDs of different brand & capacity
  • Case Material
  • High quality aluminum for optimized heat dissipation
  • System Requirements
  • Windows 7 / Windows 8.1 / Windows 10
  • Mac OS X 10.8 or later
  • Power adapter:
  • AC input: 100V~240V
  • DC output: +12V/3A
  • Color
  • black
  • Accessories Included
  • Main Device X1
  • USB Cable (Black color,1m) X1
  • QIG X1
  • External Power Adapter X1
  • Screw for HDD fixation X4
  • Product Weight & Dimensions
  • 145(D) x 80(W) x 171(H) mm
  • Weight 490g