AvailabilityIn stock
  • Support 3.5" 8 Bays SATA III HDD Maxcapacity 8 TB per drive (8 x 8 =64 tb)
  • SATA III Transfer rate up to 6Gbps
  • Support JBOD / RAID 0, 5, 10, 50
  • USB 3.0Transfer rate up to 5.0 Gbps
  • Support Hot-Swap
  • eSATA Transfer rate up to 6.0 Gbps
  • LED status indicators.
  • Gbps Smart Fan
  • 1 Years Waranty By Back-n.co.ltd.,
  • ฿16,900.00

    10 Times Faster

    The full-duplex data transfers capability allows the sending and receiving of data (at the same time) at 10 times faster than an equivalent card of USB 2.0 Standard. The maximum speed of USB 3.0 is 5Gbps, which enables the data transfer up to 25GB within a minute.

    Supports 32 TB

    Maximum addressable capacity 32TB via the USB 2.0 / USB 3.0 interfaces. Native 4KN Hard Drive Not Supported.


    Powers off in synchronizatin with PC.

    HDD X 8 (Supported)

    All 8 HDDs are recognized when they are installed.


    Comes with auto / manual modes & 3 levels of speed for best convention. Smart Fan functions:

  • Thermal-sensor built-in
  • Auto & manual modes
  • 3 levels of speed

  • Single Mode

    Non-RAID: (Single Mode) Computer will show up as two independent drives. This function can be used if RAID is not required, if one HDD is installed or two different brands or capacities of HDD are installed.

    Spanning Mode

    Spanning concatenates multiple hard drives as a single large volume; resulting in a seamless expansion of virtual volumes beyond the physical limitations of separately connected hard drives. The data are written frim HDD1 to HDD8. RAID 0, JBOD Spanning Only, Non-Single JBOD

    Striping Mode

    Striping is a method of concatenating multiple hard drives into one logical storage unit. It is the automated process of writing data across multiple drives simultaneously. Striping is used to increase the performance of disk reads. The multiple hard drives will write data in “column” effect. If one drive in a striped set fails, all of the data in the stripe set is lost.

    RAID 50

    RAID 50 combines multiple RAID 5 arrays with RAID 0 Striping. RAID 50 offers highest level of redundancy and performance. RAID 50 can sustain one to four drive failures while maintaining data integrity if each failed disk is in a different RAID 5 array. In RAID 50 the total addressable volume is 2 times the smallest layer of RAID 5 array. RAID 50 requires at least 6 Hard drives.

    RAID 1 + 0

    RAID 1+0 is mirrored(Raid 1) sets in a striped(Raid 0) set .

  • USB 3 .0 Super speed / e-SATA
  • Data Transfer Rate
  • USB 3.0 : up to 5.0Gbps
  • e-SATA : up to 3.0Gbps
  • Maximum HDD size
  • 4TB x 8
  • Multi-funtion LED displays
  • 2-color LED for power or sleeping mode Interfaec link LED display Rebuild LED display HDD error LED RAID mode LED display 3 levels of speed Manual / auto fan control
  • Fan Function
  • Smart fan function (FAN: 80mm x 80mm) X2
  • HDD
  • 3.5″ SATA I / II / III HDD *SATA III at 3.0 Gbps SATA II speed. 8HDDs with same capacity / model / brand strongly recommended
  • Operation Environment
  • Temperature 0~60 ℃ Humidity 90% RH
  • System Requirements
  • Windows 7 / Windows 8 / Windows 10 (under MBR partition, supports total capacity up to 2TB only)
  • Windows 7 / Windows 8 / Windows 10 (with GPT partition enabled, supports total capacity of more than 2TB)
  • Mac OS X 10.8 or later
  • Power adapter:
  • AC input: 100V~240V
  • DC output: +12V/3A
  • Color
  • black
  • Accessories Included
  • e-SATA cable X1 / USB 3.0 cable X1 / power adapter X1
  • power code X1 / screw driver X1 / handle X4 / user manual X1
  • HDD Handle X8/Screw driver X1 /QIG X 1
  • Product Weight & Dimensions
  • 253(D) x 155(W) x 352(H) mm
  • Weight 5000g